Happy Giving Tuesday 2019! (+ Coupon Code)

Happy Giving Tuesday! Did you know we donate a percentage of profits from Birch Landing Home at year-end? So every time you place an order or visit my blog that donation gets the chance to grow. Last year I was able to donate to The American Cancer Society and Susan G. Komen.

I haven’t decided where this year’s donation is going yet so if you have a favorite charity please share! 

And this week I’m giving back to you with a Coupon Code too! Use GIVINGBACK to get 10% off your Etsy orders through 12/11/19.

DIY Vintage Pie Tin Clock

Rummaging around in my parents basement a few weeks ago, I stumbled across a stack of Vintage Table Talk Pie Tins that had been my Grandmother’s. Back in the day (approximately the 1930’s-1950’s), people would buy these store-bought pies with an extra 10 cent deposit that would be reimbursed if you returned the clean pie tin back to the store… but apparently my Grandmother chose not to, haha. These pie tins were a fun vintage find, and sentimental because they had once belonged to her. Since we didn’t have a kitchen clock I figured turning one of these tins into a clock would be a fun idea - and here’s how I did it. | This post contains affiliate links |

The first step to creating your clock is to purchase a clock kit that has the right diameter hands for your pie tin, so when they are mounted in the center of the tin they can move freely all around the face without touching the sides (very important).

After some measuring and browsing around on Amazon, I settled on this Mudder Clock Kit - I liked the style of the hands and they would fit perfectly in my particular pie tin.

Next, carefully measure to find the center of the pie tin and poke a pilot hole through with a small nail and hammer. After that, make sure your pie tin is well supported and on a safe area for drilling (I used some scrap 4x4 posts as a work station). Then carefully drill out your hole, starting with your smallest drill bit.

In order not to “rip” the tin, it’s very important to start small and work your way up in drill bit size. I started with the smallest drill bit and then worked my way up, using every-other-drill bit in the set going up in size order.

If you get a large burr, carefully cut it off with a pair of small wire cutters before you move up to your next drill bit size.

Please note: Keep in mind that these pieces of tin are SHARP so use care and be mindful of the metal shavings you may drop while drilling. Make sure to clean up the shavings well after your project is done.

Periodically check to see if the threaded clock mechanism can pass through your hole yet. For this clock kit, I needed to jump up to a larger drill set in order to finally work my way up to the size hole I needed (in this case it was a 5/16” drill bit).

Once the hole is the correct size, use a round file to clean up any little burrs around the edge.

Now it’s time to assemble your clock - follow the manufacturer’s directions on the best way to assemble the clock hands for your particular kit. Keep in mind that clock kits and especially the hands are VERY delicate so take care assembling them.

Once your clock is assembled, install the battery and set the time - now you can enjoy your new Vintage Pie Tin Clock!

---

Are you interested in making your own Vintage Pie Tin Clock but need a pie tin?

I’m selling some extra pie tins* in my Etsy shop, click the button below to shop:

*Please note the tins I have listed for sale may vary slightly in size and style from the one I made my Pie Tin Clock with.

---

Other posts you might enjoy from Birch Landing Home:

• Milk Can House Number

• How to Turn a Starbucks Bottle into a Milk Bottle Vase

• DIY Slate Garden Markers

---

---

Art Cart Solution for Kids' Craft Supplies

Our kids love arts and crafts, and at this age, they particularly love coloring and coloring books - however, the art supplies were totally taking over the house. In order to contain the chaos, I decided an “Art Cart” would be the perfect storage and organizational solution. | This post contains affiliate links |

I picked up this cart at Target, but I've linked a very similar one here from Amazon. We decided to stash the coloring books on the bottom shelf, then the tins full of stickers and art kits on the second shelf, and finally the top shelf was reserved for our Art Supply Caddy full of crayons, colored pencils, stencils, etc.

For the Art Supply Caddy, I used an inexpensive plastic caddy and made custom vinyl labels with my Cricut so that everything has a place.

Finally to store everything, the Art Cart tucks neatly into our pantry where it’s easily accessible but still out of the way. The kids can go in and help themselves to craft supplies whenever they like, and when we want to do a big project the whole thing can wheel out for even easier access. This storage hack has been a game changer in our home and I hope it does the same for you too :)

Make Sure You're Visible on Halloween

It’s so important that kids and chaperones can be seen by motorists to help avoid any accidents, so to remind everyone of this basic Halloween safety tip - make sure you can be seen and seen well while out Trick-or-Treating. | This post contains affiliate links |

Some Ways to Increase Visibility While Trick-or-Treating:

• Carry a Flashlight. Make sure everyone in your group has a flashlight so that everyone can see where they're going and others can see you better too. (It's also a good idea to remind your kids not to shine them in others eyes as you come across other trick-or-treaters.)
• LED Bracelets/Wearables. These bright, colorful, often flashing lights can really help you be seen at night - and kids think they're really fun.
• Glow Sticks. Glow Sticks and glow jewelry can be useful to help be seen at night, and kids generally love them and will wear them without a fight.
• Reflective Stickers/Patches. We put reflective stickers on our Halloween buckets (pictured above) to help make them more noticable at night. It's hard to capture it on camera, but these stickers reflect really well in low-light conditions and are super durable, even on fabrics. (For what it's worth, we put these on everything year-round - helmets, bikes, backpacks, hiking gear, coats, etc. We love them!)
• Stay Together. Having everyone in your party stay together in a group is a great way to increase visibility. When kids scatter and dart around it can be very disorientating for drivers and hard to see where everyone is. Make sure your group stays together and walks on the sidewalks or off the shoulder of the road. Also make eye contact with stopped drivers before you cross the road to ensure that they do see you.

For specific ideas about what’s recommended in your area for safe Trick-or-Treating, contact your local public safety or Police department for more ideas. Stay safe and Happy Halloween!

Why We Skipped the Infant Car Seat

Picking a car seat for the baby you’ll soon be bringing home is such a stressful choice - so many options and opinions out there! Ultimately do your homework and pick the car seat that you feel is safe, fits your lifestyle, and fits correctly in your car. For us, we decided to skip the Infant Car Seat completely (don’t worry, we still used an appropriate car seat, I’ll explain) and I’ll tell you why we did… | This post contains affiliate links |

When my sister had her first baby I remember helping her carry the baby in her Infant Car Seat when she was about one or two months old and thinking (excuse my language) “this sucks!” It was exhausting, and extremely awkward to carry the weight of the baby and carseat (probably around 25 lbs total) by a handle away from your body, trying not to let it bump into your legs or anything else around you. Depending on the model of infant car seat you buy the seat itself can weigh 11-20 pounds, then you add the weight of the baby which will be an average of 6-9 pounds at birth and quickly get heavier as time goes on. That’s a lot of weight to awkwardly haul around.

However, my sister-in-law had decided to skip the infant car seat all together for her kids, and opted for a Convertible Car Seat from day one. I thought this was genius and we decided to do the same. A true Convertible Car Seat is one that’s good from birth through a particular weight limit, typically fairly high. For us the seat we chose was good for 4-65lbs, which meant that it would be rear-facing and perfect for bringing home the baby from the hospital and could grow with us and eventually convert to a forward-facing carseat up to the 65lb weight limit (which will take them into elementary school-age most likely) - and some Convertible Car Seats even go up to a 120lb limit!

By going with a Convertible Car Seat from day one, we only had to purchase one car seat instead of two, as most babies will outgrow their Infant Car Seat well before the age of one. Rather than buying a car seat that would only get used for several months, we invested in one that would grow with our baby and our needs. This saved us money in the long-run, and was less wasteful on the environment.

Since the Convertible Car Seats stay in the car (they don’t disconnect from a base and get carried around like an infant seat), I chose to wear our baby whenever we got to our destination with a Soft Structured Baby Carrier. I found this to be far more convenient and easier than lugging around an Infant Car Seat. Wearing your baby is also great for bonding, can help keep them healthier (they’re closer to you and less likely to be touched by strangers), and so much better ergonomically for your back and body than carrying an infant seat.

But what about waking up the baby, people ask? Yes, you tend to rouse the baby a little when you take them out of their car seat. But they reality is, it’s not recommended for them to sleep in their car seats for any signifiant amount of time as it can supposedly increase their risk of SIDS. Anyways in our experience with our two kids, they often woke up when we turned off the car, before I even tried to take them out of their carseat. And if they are tired enough, you should (hopefully) have no trouble getting them to go to sleep in their crib once you get home.

*Disclaimer: I am not a car seat expert, and my opinion should not be taken as fact. I am simply sharing our opinions on why we preferred a Convertible Car Seat over an Infant Car Seat. Before making your carseat decision, do your homework and discuss your options and concerns with your pediatrician and car seat experts like Car Seats for Littles.*

DIY Potting Bench - Based on Plans by Ana White

I’ve been wanting a potting bench for a while now - something by the back door to display some decor, use as an outdoor work station, and double as a place for UPS to leave packages. After looking around online and at local stores, I couldn’t find anything that I liked that fit the narrow space - so I did what any #woodworkingmom would do, I decided to build it myself. | This post is not sponsored but does contain affiliate links |

{ Note: The plans I worked from were from Ana White and can be found HERE }

I came across these Ana White plans for a Simple Potting Bench on Pinterest and thought it was perfect! It was exactly the simple, rugged style I was looking for and easy to tailor to our space too. Most of the wood needed were 2x4’s, which are sturdy and cheap - and thankfully between our garage and my father-in-law’s garage we had all the wood scraps I needed to piece together this project. Since I used leftover wood we already had, this project cost me nothing which was pretty amazing!

Since I only used what wood we had on hand, I had to make do - some of the wood was pressure-treated, some was not, some had knot holes or gashes, and not all of it was “true” (straight). But that was fine by me as this was to be a rustic piece for outside.

Before I started building, I followed Ana White’s “cut list,” cutting and making piles of all the wood in the dimensions I would need to build the project. I carefully chose the lumber for each section to minimize how the knot holes, gashes, or crooked pieces would be seen in the final piece. For our potting bench I made it 4 inches narrower so it would fit against the small wall next to our back door and because of this I had to adjust my cut list and refigure some of the overall dimensions.

The next step was constructing the shelves individually - attaching the outer planks first, checking for square, then spacing out the middle planks and attaching them. To build this whole project I used an Impact Driver, which made the entire project go much quicker and easier.

To attach the legs, I laid the project on it’s side and carefully measured the distances between the legs as well as up the legs before attaching the shelves to makes sure everything would be as level and as square as possible.

Finally to make the project look more “finished” I added some wood scraps to the sides of the project to conceal the butt ends of the shelves and make it look a little more polished.

I also decided to add some 1x3”s to the front of the shelves to make it look a little more polished from the front as well. (I did not counter-sink these screws, but I should have as they were more noticeable than I was expecting in the finished piece.)

Then came time for painting - I chose to paint the whole potting bench in several coats of my favorite Valspar Stainblocking Bonding Primer/Sealer. This stuff has great coverage and really covers and seals well. My one regret was not giving all the wood pieces a single coat of paint before assembling - as once everything was assembled it was a huge pain to get in all the nooks and crannies.

Finally I finished the project by adding a few little hooks underneath the shelf (very similar hooks linked here), from which I can hang tools or decor. I’m really happy with how this came out and how quickly it came together. I can’t wait to decorate it with some plants come next spring!

PS - I’m thinking this potting bench would also be great for parties and BBQ’s! It would be perfect on a patio or deck as a makeshift buffet table.

UPDATE: Spring, 2020

Just wanted to give a quick update after I made the potting bench last Fall: Over winter we decided to store it in our shed, just so we wouldn’t have to snow blow and shovel around it all winter, but as soon as the threat of snow passed in early Spring we brought it right back out. It’s been wonderful to have for planting and working on outside this spring, and due to the current Pandemic situation we’re getting more packages than ever so it’s great to have a designated spot for deliveries (and right in view of our security camera too).

For decor right now I'm keeping it very simple, especially since the potting bench is utilized daily for mail - there's just a garden rock, a metal barn star (hung from a special hook that doesn't damage vinyl siding), and a small potted lavender plant with an American flag - all items we already had around our house.

Summer, 2020 - sharing another little decor update for the potting bench:

I found this weathered piece of wood in our scrap bin and thought it would make a cute sign for the potting bench. I used my Cricut Machine to design and cut a stencil that said "Fresh Cut Flowers 5¢" and used it to paint the sign. I think it looks cute and it's a great finishing touch!

---

Check out our Similar Posts:

Why My Blog Will Never Make a Lot of Money (and why I'm okay with it)

First off, no disrespect to my fellow bloggers and blogger friends. Blogging professionally is HARD and so much work - maintaining a following, meeting deadlines, constantly creating and promoting content, and so much more. So many people work tirelessly on their blogs every single day in order to grow it and provide income for their families - and I absolutely applaud that. However, there are a lot of common aspects of blogging that I am personally not okay with… and while it holds me back from making this blog lucrative, I’m more than okay with it - and here’s why…

I Don’t Overshare

Most blogs with a dedicated following tend to share everything about their daily lives - what they’re wearing that day, what they did, what they ate, what silly thing their kids did, what personal roadblock they’re encountering, etc. And I like my personal life, well - personal. I won’t be constantly on Instastories narrating my life, sharing all the details throughout my day. And I confess, some of my favorite blogs to follow do just that - I’m guilty of enjoying their stories and living their life vicariously through them. It’s interesting and fun and a great way to get an engaged following - but I could never do that myself. I personally find it too intrusive and creepy to have so many people know so much about our personal life.

I Won’t Sell Out My Kids

Promoting kid and baby items/gear is a huge market in the blogging industry. So many brands seek out bloggers with kids and growing families and hire them to help promote their products. In turn, bloggers share tons of photos of their children wearing or using the products, along with personal stories to make it more interesting. For example, a blogger may choose to take a sponsored post about a potty seat. In doing so, she may choose to share photos and stories of her kids potty training… now can you imagine being that child and having that digital footprint/history when they grow up? It would come back to haunt him in high school or if he ever ran for Congress.
Now, I do work with some select kids brands and products - however I’m particular with who and how I work with them. I only share about products and brands we honestly love or use, and I limit the photos I post of our children. Typically when I share photos of our kids on the blog they are carefully cropped or edited to help protect their anonymity - this is super important to me but definitely limits the brands that want to work with me, as most brands want tons of personable photos.

I Follow the Rules

I always do my best to follow the rules regarding sponsored content and outbound links. There are a lot of guidelines out there from the Federal Trade Commission (FTC) on how sponsored content and affiliate links need to always be disclosed and outbound sponsored/affiliate links should be formatted as “no-follow” (in order to not falsely inflate a product or brand’s Google-ranking). Unfortunately there are a lot of unscrupulous companies out there that will solicit bloggers to create posts or add back-links that completely go against these rules. I have been solicited several times (and a few times by large companies that should know far better), asking me to add “do-follow” links or mention product without disclosures in exchange for compensation. I always turn these shady offers down (and scold them for being unethical).

I Have Standards

I will ONLY accept sponsored posts from products and brands we honestly use or are interested in. I will never accept a sponsored post from something that doesn’t fit my blog, my beliefs, or me. I have turned down many sponsored posts for products that do not fit my aesthetic or would have me promote a product we do not like or would never use.

I Don’t Live in an Instagram-Worthy House

We live in a very average house with very average finishes and furniture. Our kitchen is still sporting it’s laminate green (yes, green) counter tops and linoleum floor and our living room still has the very bold (and ugly) burgundy wall-to-wall carpet that were installed when our house was originally built. Would I love to renovate and re-do these things? Absolutely. But it’s not in our budget right now and not a priority, so we’re going to continue to live with these less-than-beautiful finishes. Many bloggers completely re-renovate or re-decorate the same rooms in their home over and over in order to keep up with the latest trends and to continue to land partnerships. And as fun as that might be, it’s also very wasteful and encourages a “throw-away society” that values consumerism and disposable items over value and longevity.

I Don’t Stick to a Content Schedule

Sticking to a content schedule is something I really should be better about. I already keep a blog calendar over my desk and pencil in a few blog topics or content I want to create over the course of each month. However, I’m terrible at sticking to it… life gets busy. Lately we’ve been keeping busy with family, sports, appointments, and school. Keeping up with the kids is most important and so I try to be flexible (arguably far too flexible) with the blog. Sometimes I don’t do a blog post or Instagram post for a week… or three! That’s as good as a death sentence for engagement, which is already SO hard to achieve these days with Instagram’s increasingly difficult algorithms.

So in conclusion, if you want your blog to be lucrative - consider doing the opposite of all I do. I’ll be over here, not making much money but content in my principles ;)

Out and About with the Eddie Bauer Places & Spaces Cascade Diaper Backpack

Almost six years ago, we got an Eddie Bauer Diaper Tote Bag before our first was born - and ever since it has been our go-to diaper bag for the car and outings. We’ve loved it’s durability and functionality, so when we had the opportunity to try one of their backpack styles with our littlest one we jumped at the chance! | Sponsored - This post contains an honest review of product provided by Eddie Bauer c/o Baby Brezza |

In the past when doing long outings on foot I’ve always thrown diaper bag items into one of my regular hiking backpacks, and inevitably whatever we needed most would always be lost at the bottom somewhere. Hiking backpacks just aren’t ideal for holding all the little items, wipes, diapers, bottles, etc you need - so you can imagine how excited I was to finally try a backpack that was made to be a diaper bag!

I was particularly drawn to the Eddie Bauer Places & Spaces Cascade Diaper Backpack for it’s looks and functionality. I loved that it looked like a fun, modern bag that didn’t scream “diaper bag.” I also loved all of it’s features! It has twelve (yes, 12!) pockets, removable changing pad, stroller loops, wipes case, and insulated bottle pocket. No more digging around to find small items with all of it’s handy pockets! And the wipes case on the side is great for getting a wipe on the go to clean messy hands or faces.

Our family has been loving the practicality and style of this diaper backpack and are really looking forward to bringing it to the local country fair in a few weeks! Being hands-free is key to keeping up with the little ones ;)

SHOP THIS POST: | Eddie Bauer Places & Spaces Cascade Diaper Backpack (exclusively at Target) | L.L. Bean Sweater Fleece | White Mountain Shoes Skipper Leather Moccasin | Polo Ralph Lauren Bal Harbour Toddler Sneakers | Toddler Rain Jacket is old L.L. Bean |

- I received this Eddie Bauer diaper backpack from Baby Brezza but all opinions expressed are my own.  Please read our full Disclosure Policy for more information -